I love making little Artist Trading Cards, but often I want to use clip art or collage images that are too big to fit on them. Here is a simple guide to how to resize your digital clip art to fit your ATCs – or indeed any project you are making.

I am using Photoshop but you could do this in any graphics program that allows layers, such as GIMP (free!) , Adobe Photoshop Elements, Paint Shop Prop, Affinity Paint, Adobe Illustrator etc. Your software may look a little different to my screenshots, but the principles are just the same.

First, I create a new document that is the size of my finished project. So in this case, I create a blank document that is 3.5 inches tall and 2.5 inches wide. This is the standard size for an ATC (if you don’t know what ATCs are, see my article Introduction to Trading Cards).

I set my new document to 200dpi as this will print nicely.Artist Trading card dimensions - saved as a custom preset

I have saved my ATC sized document, so I can easily use it again in the future.

Now for the clip art. I want to use the cute little Frankie character from the Tin Teddy Frankie & Ezzie Clip Art set. I am going to make ATCs using the four standing images of him.

I opened the four images into Photoshop. I have all four open at once.Four little Frankies, ready to use

Then I dragged three of the images on to the fourth one. Frankie 2 is the widest, so I dragged the others on top of him. In Photoshop, and many other graphics programs, if you hold the shift key whilst you drag an image into another, it will end up perfectly centered in the new document.

Here is my pile of Frankies.All the Frankies, in a pile, in one document

To make the next step as easy as possible, I resize the pile of images in two stages.

I opened the resize option. The resolution of these images is 200dpi, the same as my ATC document, so no change needed there. If it were different, then I would change this to match before doing anything else.The original size of the Frankies

Now I change the dimensions to use inches, and set one of them, so it will fit on the ATC.

So my original Frankie images are 9.624 inches high and 5.554 inches across – far too big to fit on an ATC.

I will change the height to 3.5 inches. The width automatically adjusts to match.

If your images are wider than they are long, change the width to fit. This is not the final re-sizing, it is just a shortcut for later. Make sure that “Constrain proportions” is ticked before you resize, or else you will end up with a very strange shaped Frankie!And the new size, so they will fit an ATC

Next, I clicked on the bottom Frankie layer, then held the shift key and clicked on the top Frankie layer – so all the Frankies were selected.

And I dragged them all into the blank ATC document that I made at the start.

Whilst they fit on the card (just) they are a bit too big for what I want. I will be adding other things to the ATC so do not want Frankie to cover so much area.The Frankies are resized now

Make sure that you still have all four Frankies selected, then hold the shift key and carefully resize the Frankies until they are the size you will actually want them to be on the ATC.Now I resize them some more, so they will fit perfectly

Finally.. open a new document the same size as the paper you will be printing your Frankies on. I sometimes use 6″ x 4″ photo paper for when I only have a few things to print. But here I am going to use a sheet of A4 sized paper (A4 is very close to Letter size). Make sure the resolution is set to the same dpi as you have used for the ATC document and the clip art – in this case, 200dpi.Creating a new blank page

Drag the pile of freshly resized Frankies into the new A4 document.The Frankies have been dropped on the page - ready to spread them out

Now just move the individual Frankies around, so they all fit on your page. The picture below show just the upper part of the page (because the rest is just boring white).Here are the Frankies, ready to print

Add anything else you wish to print at the same time…. and hit print!

Handy hint – I ALWAYS save my reduced pile of Frankies, and the finished document, before I print it. Just in case. Or you may want them again another day, and this saves having to reduce them all over again.

This technique takes a lot longer to explain here than it does to actually do it! And once you have done it once, the next time will be much faster.

There are other ways to reduce clip art to fit a specific project, but I usually use this technique as it is very easy to see exactly what I will get.

And now you can cut out each Frankie, and fix it to your Artist Trading Cards.

If you would like to know more about ATCs – Introduction To ATCs – What are Artist Trading Cards

Get your own Frankies (and some Ezzies) here

How to Resize Clip Art to fit an ATC (Artist Trading Card)

One thought on “How to Resize Clip Art to fit an ATC (Artist Trading Card)

  • 9 October, 2015 at 3:13 pm
    Permalink

    Thank you for explaining this

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.